Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
Were you on the lookout for insight on Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably challenging task. If the old bathtub is conveniently available, the task can relocate immediately; if you need to open up a wall surface to get rid of the old tub and position the brand-new tub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the work and also are comfortable trying it. Instead of working with a professional to take control of a halfway-completed task, it is better to take into consideration utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will certainly help you set up a brand-new tub in your bathroom if you have currently acquired a brand-new tub and also don't need to transform the plan of your previous water pipes.
Your devices and also material checklist need to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in location between the faucet as well as the sink. Safeguard the faucet in position with the supplier offered backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the tub in the called for setting. The wooden boards are practical in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub till the spirit level reads degree.
To install taps, fit the bottom of the furthest flexible tap connector to the proper supply pipeline by making a compression join; after that do the very same for the other tap.
Switch on the water supply and also check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the tub and additionally examine the overflow outlet and the normal outlet for leaks.
Lastly, fix the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the tub must wait until the bathtub has actually been utilized at least when as this will certainly settle it into its final position.
Getting ready for the Installment
To start with, the supporting framework supplied with the bath should be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture an inflexible seal, creating the water to pass through the wall between the bathroom and also the tiling, bring about problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that editorial on Installing A Bathtub through an acquaintance on our other web property. So long as you enjoyed reading our post please remember to pass it around. We appreciate reading our article about How to Install a Bathtub.
Save time, dial! Report this page